 |
 |
OZ ATV :: The Australian ATV Forum
Australia's Largest ATV Forum
|
|
|
|
|
|
|
|
|
|
|
robbo350
50cc nipper
Joined: 09 Dec 2008
Posts: 8
Location: perth
|
 Posted: Sat Dec 20, 2008 2:23 am Post subject: banshee help |
  |
|
hey all just wondering if anyone can tell me if there is someone in aust that sell the complete TORS removal kits for the banshees
any help would be great
cheers
Rob
_________________
98 model banshee runnin-fmf gold series fattys
k&n filter, k&n powerlid,boysen reeds with spacer,razor2 tyres at rear,razors up front,nerfs |
|
| |
|
|
|
|
|
|
|
|
Sponsor
|
|
|
|
|
|
|
|
|
Overlord
4fiddy Racer
Joined: 17 Jan 2007
Posts: 272
|
| Posted: Sat Dec 20, 2008 4:52 am Post subject: Tors Removal |
|
|
Hi Robbo, last time I heard Andrew from Austraco was selling the Tors Removal kits. A word of warning most people I have spoken to say the throttle action goes real heavy when you remove it. I never had a problem with mine so I left it. If you do use the Tors Removal you may have to change your thumb throttle to a better one like a Honda 450, KFX 700 or even a Dual Gaser to make the throttle action lighter. Yamaha make the worst thumb throttles in the world when you change to one of the above you will get a lot better action and a lighter throttle. You can buy a Dual Gaser from JMC racing for around $180 nice product to. Also JMC may have the Tors removal kit as well.
Regards Bad Banshee |
|
| |
|
|
|
|
|
|
|
|
robbo350
50cc nipper
Joined: 09 Dec 2008
Posts: 8
Location: perth
|
| Posted: Sat Dec 20, 2008 9:20 am Post subject: |
|
|
ok cheers
whats involved with putting another thumb throttle setup from another brand bike?
Rob
_________________
98 model banshee runnin-fmf gold series fattys
k&n filter, k&n powerlid,boysen reeds with spacer,razor2 tyres at rear,razors up front,nerfs |
|
| |
|
|
|
|
|
|
|
|
doorslammer
Roostin Away
Joined: 24 Jul 2007
Posts: 902
Location: Northern WA
|
| Posted: Sat Dec 20, 2008 2:58 pm Post subject: |
|
|
i have a set of brand new PE 28mm carbs for sale, all you need is a Motion pro throttle cable for banshees without tors and it will bolt straight in. this can go onto aftermarket thumb throttles or a twist throttle kit.
most of the supliers will have these or will get them for you
good upgrade to go with what you have now.
_________________
01 Banshee
Never take life seriously. Nobody gets out alive anyway |
|
| |
|
|
|
|
|
|
|
|
Overlord
4fiddy Racer
Joined: 17 Jan 2007
Posts: 272
|
| Posted: Sun Dec 21, 2008 5:41 am Post subject: Banshee Thumb Throttle |
|
|
Hi Robbo, make sure you have enough room on ya bars as some like Pro Tapers can be a bit short to fit everything on, if you run standard bars you got no worry's. Just disconect the electrics on the throttle, tape up the end and stuff them behind a panel, connect the cable, adjust and ride. Make sure you check the prices on the Honda and Kawasaki throttles could be around the $250 mark and like I said you can buy a Dual Gasser for $180 (little bit harder to fit but well worth it) Mate if your not haven trouble with the Tors leave it. I hade no problem with mine I just changed the throttle and it was sweat to ride.
Regards Bad Banshee |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
© 2001, 2002 phpBB Group
|
|
|
