OZ ATV :: The Australian ATV Forum

[angus350]

im gonna get graphics soon and was wondering if theirs any tricks to putting them on and not stuffing them up.

also anyone got pics of spastic graphics on bikes ? because at this stage im looking at gettin them. i have seen sicmic (i think) and his look sic but havent seen any others.

thanks

benn
_________________
BENNO

[OZ_450]

ok ben our 2 ltrs have spastic kits on em in show us ya ride section also search for jono post his yfz has em aswell

or shoot Adam a email at quadsquad he has pics of his on his yfz aswell or could help you with some photos i am sure
_________________
black covered in 5.7 powered oversize quad
model vx ss 350 hahaha
enough bass to compensate for lack of skills
Empty Wallet Racing proudly on track for GM Motorsport

[peg_leg686]

hey does anyone know if you can get graphics kits for the raptor 660 i looked on spastics site but they dont list them. is there any other brands out there???
_________________
01 RAPTOR 660. 55RWHP

[bullet]

Hi Benn
My old TRX has a Spastic Designs graphics kit fitted and is pictured on the bottom of page 10 in the Show us your ride thred of General Chit Chat.

I found the stickers very easy to fit.
Just be sure the plastics are super clean and you can get a few goes at peeling them back a bit and doing corrections.
Once you are done they stay down well.
My pressure washer has never lifted a corner of the spastics stickers where it usually blows my race numbers and other stickers off really quickly.
_________________
Can-Am X Team
Bullet #Y12. MrsB #Y18.

[angus350]

yeah i was told some come off easy with pressure washer

i have already emailed adam from quadsquad and as soon as i get some cash ill probably order these one






cheers for the info

benn
_________________
BENNO

[OZ_450]

i have that kit on my ltr suzuki

and also Ryan Lancaster has same one on his yfz

small spray bottle of water mist spray it on plastics then apply sticker kit and then squeegy water out then use hair dryer to mold any tight curves heat and move with hands then let dry for 24 hrs
_________________
black covered in 5.7 powered oversize quad
model vx ss 350 hahaha
enough bass to compensate for lack of skills
Empty Wallet Racing proudly on track for GM Motorsport

[hammer686]

peg_leg686 wrote:

hey does anyone know if you can get graphics kits for the raptor 660 i looked on spastics site but they dont list them. is there any other brands out there???

http://www.xgxracing.com/index2.html

used these on 660 fit ok very thick film.
_________________
Raptor 700

[angus350]

OZ_450 wrote:

i have that kit on my ltr suzuki and also Ryan Lancaster has same one on his yfz small spray bottle of water mist spray it on plastics then apply sticker kit and then squeegy water out then use hair dryer to mold any tight curves heat and move with hands then let dry for 24 hrs

i can see myself stuffin it up already haha

and the gap between the plastics does it just come in 1 piece and you cut between it afterwards ?
_________________
BENNO

[Quad Squad]

angus350 wrote:

OZ_450 wrote: i have that kit on my ltr suzuki and also Ryan Lancaster has same one on his yfz small spray bottle of water mist spray it on plastics then apply sticker kit and then squeegy water out then use hair dryer to mold any tight curves heat and move with hands then let dry for 24 hrs i can see myself stuffin it up already haha and the gap between the plastics does it just come in 1 piece and you cut between it afterwards ?

They come pre-cut Benn, so you only have to install 1 section at a time. its not too bad if you take your time.
_________________
www.quadsquad.com.au
Follow us on Facebook http://www.facebook.com/atvracetechnology

[peg_leg686]

http://www.xgxracing.com/index2.html

used these on 660 fit ok very thick film.[/quote]

You dont have any pics of it do you hammer???
_________________
01 RAPTOR 660. 55RWHP

[hammer686]

2nd from bottom of page on link below

http://www.ozatv.com/forum/viewtopic.php?t=2079&postdays=0&postorder=asc&start=50
_________________
Raptor 700

[gammie61]

OZ_450 wrote:

small spray bottle of water mist spray it on plastics then apply sticker kit and then squeegy water out then use hair dryer to mold any tight curves heat and move with hands then let dry for 24 hrs

Try a couple of drops of dishwasher soap in the squirt bottle.
Wet down the surface with that & you can move the stickers around easily.
Use a credit card to squeegie the excess water out from under the stickers. Don't pannic about small water bubbles. They dry up eventually.
Not too sure how it will go on tight bends. Tell us when your done.
_________________
06 LTZ400
2000 BANSHEE
Lousy rider.
Eats lots mud now it's wet.