 |
 |
OZ ATV :: The Australian ATV Forum
Australia's Largest ATV Forum
|
|
|
|
|
|
|
|
|
|
|
fossil800R
The Day Starts With OZATV !
Joined: 22 Aug 2007
Posts: 1166
Location: Barkly, Victoria
|
 Posted: Fri Jul 02, 2010 9:42 am Post subject: Wanted to swap. Pro Armor Revolution nerfs. Done.Thanks Quad |
  |
|
Due to a shipping error, I have a set of brand new black Pro Armor Revolution nerf bars with solid heel plates to suit an '09 YFZ450R that I am looking to swap for something I can use on my Raptor. A set of Flexx bars would be good or some rims. Let me know what you have.
They look like this but black....
_________________
I'm not suffering from insanity, I'm enjoying it!!!
Last edited by fossil800R on Sun Jul 04, 2010 10:09 pm; edited 2 times in total |
|
| |
|
|
|
|
|
|
|
|
Sponsor
|
|
|
|
|
|
|
|
|
triple"A"
Roostin Away
Joined: 04 Aug 2006
Posts: 941
|
| Posted: Fri Jul 02, 2010 9:17 pm Post subject: |
|
|
| what sort of rims would tempt you? |
|
| |
|
|
|
|
|
|
|
|
fossil800R
The Day Starts With OZATV !
Joined: 22 Aug 2007
Posts: 1166
Location: Barkly, Victoria
|
| Posted: Fri Jul 02, 2010 9:36 pm Post subject: |
|
|
| triple"A" wrote: | | what sort of rims would tempt you? |
A couple of rear beadlocks would be good. Obviously there may be a difference in price. I would prefer the bars though but not too many people have them.
_________________
I'm not suffering from insanity, I'm enjoying it!!! |
|
| |
|
|
|
|
|
|
|
|
Noy Q75
Roostin Away
Joined: 16 Nov 2007
Posts: 943
Location: Perth W.A.
|
| Posted: Fri Jul 02, 2010 10:38 pm Post subject: |
|
|
i will swop you a set of flex bars for them  there straight but the holes are a little worn out were they pivot up and down so they move backwards and forwards a bit on the bit were it pivots. i slight weld and clean up the hole and they should be sweet. ( i tryied to clean out the holes when i cleaned the bike up and as i found out that was a bad thing to do)  i still rode with them but when you are doing the state rounds they didnt like them movment were there shouldnt be any  i have been meaning to get them welded but not had the time. the hole is .5mm over the size it should be but that makes a big diffrence on the far bar end of the bars
_________________
Sponsors ,Cullys Yamaha,Pirtek Malaga
2x YFZ 450r "09" 2x 90 Raptor "09"2x 125Raptors "12"
N# 1 Aus Quad Nats Vets 2010
N# 1 at BSA-HD for 09,10,11
N# 2 W.A. State Clubman A 2010
N# 3 W.A. State Vets 2011
N# 1 W.A. State Vets 2012 |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
© 2001, 2002 phpBB Group
|
|
|
